The word "viscosity" derives from the Latin word "viscum" for mistletoe. A viscous glue was made from mistletoe berries and used for lime-twigs to catch birds.[2]
Viscosity coefficients
Viscosity coefficients can be defined in two ways:
- Dynamic viscosity, also absolute viscosity, the more usual one;
- Kinematic viscosity is the dynamic viscosity divided by the density.
Viscosity is a tensorial quantity that can be decomposed in different ways into two independent components. The most usual decomposition yields the following viscosity coefficients:
- Shear viscosity, the most important one, often referred to as simply viscosity, describing the reaction to applied shear stress; simply put, it is the ratio between the pressure exerted on the surface of a fluid, in the lateral or horizontal direction, to the change in velocity of the fluid as you move down in the fluid (this is what is referred to as a velocity gradient).
- Volume viscosity or bulk viscosity, describes the reaction to compression, essential for acoustics in fluids, see Stokes' law (sound attenuation).
Alternatively,
- Extensional viscosity, a linear combination of shear and bulk viscosity, describes the reaction to elangation, widely used for characterizing polymers.
For example, at room temperature, water has a dynamic shear viscosity of about 1.0 × 10−3 Pa∙s and motor oil of about 250 × 10−3 Pa∙s.[3]
Newton's theory
In general, in any flow, layers move at different velocities and the fluid's viscosity arises from the shear stress between the layers that ultimately opposes any applied force.
Isaac Newton postulated that, for straight, parallel and uniform flow, the shear stress, τ, between layers is proportional to the velocity gradient, ∂u /∂y, in the direction perpendicular to the layers.
Here, the constant μ is known as the coefficient of viscosity, the viscosity, the dynamic viscosity, or the Newtonian viscosity.
This is a constitutive equation (like Hooke's law, Fick's law, Ohm's law). This means: it is not a fundamental law of nature, but a reasonable first approximation that holds in some materials and fails in others. Many fluids, such as water and most gases, satisfy Newton's criterion and are known as Newtonian fluids. Non-Newtonian fluids exhibit a more complicated relationship between shear stress and velocity gradient than simple linearity.
The relationship between the shear stress and the velocity gradient can also be obtained by considering two plates closely spaced apart at a distance y, and separated by a homogeneous substance. Assuming that the plates are very large, with a large area A, such that edge effects may be ignored, and that the lower plate is fixed, let a force F be applied to the upper plate. If this force causes the substance between the plates to undergo shear flow (as opposed to just shearing elastically until the shear stress in the substance balances the applied force), the substance is called a fluid. The applied force is proportional to the area and velocity of the plate and inversely proportional to the distance between the plates. Combining these three relations results in the equation F = μ (Au/y), where μ is the proportionality factor called the dynamic viscosity (also called absolute viscosity, or simply viscosity). The equation can be expressed in terms of shear stress; τ = F/A = μ (u / y). The rate of shear deformation is u / y and can be also written as a shear velocity, du/dy. Hence, through this method, the relation between the shear stress and the velocity gradient can be obtained.
James Clerk Maxwell called viscosity fugitive elasticity because of the analogy that elastic deformation opposes shear stress in solids, while in viscous fluids, shear stress is opposed by rate of deformation.
Viscosity measurement
Dynamic viscosity is measured with various types of rheometer. Close temperature control of the fluid is essential to accurate measurements, particularly in materials like lubricants, whose viscosity can double with a change of only 5 °C. For some fluids, it is a constant over a wide range of shear rates. These are Newtonian fluids.
The fluids without a constant viscosity are called non-Newtonian fluids. Their viscosity cannot be described by a single number. Non-Newtonian fluids exhibit a variety of different correlations between shear stress and shear rate.
One of the most common instruments for measuring kinematic viscosity is the glass capillary viscometer.
In paint industries, viscosity is commonly measured with a Zahn cup, in which the efflux time is determined and given to customers. The efflux time can also be converted to kinematic viscosities (cSt) through the conversion equations.
A Ford viscosity cup measures the rate of flow of a liquid. This, under ideal conditions, is proportional to the kinematic viscosity.
Also used in paint, a Stormer viscometer uses load-based rotation in order to determine viscosity. The viscosity is reported in Krebs units (KU), which are unique to Stormer viscometers.
Vibrating viscometers can also be used to measure viscosity. These models such as the Dynatrol use vibration rather than rotation to measure viscosity.
Extensional viscosity can be measured with various rheometers that apply extensional stress.
Volume viscosity can be measured with acoustic rheometer.
Units
Dynamic viscosity
The usual symbol for dynamic viscosity used by mechanical and chemical engineers — as well as fluid dynamicists — is the Greek letter mu (μ)[4][5][6][7]. The symbol η is also used by chemists, physicists, and the IUPAC[8].
The SI physical unit of dynamic viscosity is the pascal-second (Pa·s), which is identical to kg·m−1·s−1. If a fluid with a viscosity of one Pa·s is placed between two plates, and one plate is pushed sideways with a shear stress of one pascal, it moves a distance equal to the thickness of the layer between the plates in one second.
The cgs physical unit for dynamic viscosity is the poise[9] (P), named after Jean Louis Marie Poiseuille. It is more commonly expressed, particularly in ASTM standards, as centipoise (cP). Water at 20 °C has a viscosity of 1.0020 cP.
- 1 P = 1 g·cm−1·s−1.
The relation to the SI unit is
- 1 P = 0.1 Pa·s,
- 1 cP = 1 mPa·s.
Kinematic viscosity
In many situations, we are concerned with the ratio of the viscous force to the inertial force, the latter characterised by the fluid density ρ. This ratio is characterised by the kinematic viscosity (Greek letter nu, ν), defined as follows:
The SI unit of ν is m2/s.
The cgs physical unit for kinematic viscosity is the stokes (St), named after George Gabriel Stokes. It is sometimes expressed in terms of centistokes (cSt or ctsk). In U.S. usage, stoke is sometimes used as the singular form.
- 1 St = 1 cm2·s−1 = 10−4 m2·s−1.
- 1 cSt = 1 mm2·s−1 = 10−6m2·s−1.
Water at 20 °C has a kinematic viscosity of about 1 cSt.
The kinematic viscosity is sometimes referred to as diffusivity of momentum, because it has the same unit as and is comparable to diffusivity of heat and diffusivity of mass. It is therefore used in dimensionless numbers which compare the ratio of the diffusivities.
Non-standard units
At one time the petroleum industry relied on measuring kinematic viscosity by means of the Saybolt viscometer, and expressing kinematic viscosity in units of Saybolt Universal seconds (SUS).[10] Other abbreviations such as SSU (Saybolt Seconds Universal) or SUV (Saybolt Universal Viscosity) are sometimes used. Kinematic viscosity in centistoke can be converted from SUS according to the arithmetic and the reference table provided in ASTM D 2161.[11]
Molecular origins
The viscosity of a system is determined by how molecules constituting the system interact. There are no simple but correct expressions for the viscosity of a fluid. The simplest exact expressions are the Green–Kubo relations for the linear shear viscosity or the Transient Time Correlation Function expressions derived by Evans and Morriss in 1985. Although these expressions are each exact in order to calculate the viscosity of a dense fluid, using these relations requires the use of molecular dynamics computer simulations.
Gases
Viscosity in gases arises principally from the molecular diffusion that transports momentum between layers of flow. The kinetic theory of gases allows accurate prediction of the behavior of gaseous viscosity.
Within the regime where the theory is applicable:
- Viscosity is independent of pressure and
- Viscosity increases as temperature increases.
James Clerk Maxwell published a famous paper in 1866 using the kinetic theory of gases to study gaseous viscosity.[13] To understand why the viscosity is independent of pressure consider two adjacent boundary layers (A and B) moving with respect to each other. The internal friction (the viscosity) of the gas is determined by the probability a particle of layer A enters layer B with a corresponding transfer of momentum. Maxwell's calculations showed him that the viscosity coefficient is proportional to both the density, the mean free path and the mean velocity of the atoms. On the other hand, the mean free path is inversely proportional to the density. So an increase of pressure doesn't result in any change of the viscosity.
Relation to mean free path of diffusing particles
In relation to diffusion, the kinematic viscosity provides a better understanding of the behavior of mass transport of a dilute species. Viscosity is related to shear stress and the rate of shear in a fluid, which illustrates its dependence on the mean free path, λ, of the diffusing particles.
From fluid mechanics, shear stress, τ, on a unit area moving parallel to itself, is found to be proportional to the rate of change of velocity with distance perpendicular to the unit area:
for a unit area parallel to the x-z plane, moving along the x axis. We will derive this formula and show how μ is related to λ.
Interpreting shear stress as the time rate of change of momentum, p, per unit area A (rate of momentum flux) of an arbitrary control surface gives
where is the average velocity along x of fluid molecules hitting the unit area, with respect to the unit area.
Further manipulation will show[14]
, assuming that molecules hitting the unit area come from all distances between 0 and λ (equally distributed), and that their average velocities change linearly with distance (always true for small enough λ). From this follows:
where
is the rate of fluid mass hitting the surface,
- ρ is the density of the fluid,
- ū is the average molecular speed (
),
- μ is the dynamic viscosity.
Effect of temperature on the viscosity of a gas
Sutherland's formula can be used to derive the dynamic viscosity of an ideal gas as a function of the temperature:
This in turn is equal to
where
which is a constant.
in Sutherland's formula:
- μ = dynamic viscosity in (Pa·s) at input temperature T,
- μ0 = reference viscosity in (Pa·s) at reference temperature T0,
- T = input temperature in kelvin,
- T0 = reference temperature in kelvin,
- C = Sutherland's constant for the gaseous material in question.
Valid for temperatures between 0 < T <>
Sutherland's constant and reference temperature for some gases
| Gas | C [K] | T0 [K] | μ0 [10−6 Pa s] |
|---|---|---|---|
| air | 120 | 291.15 | 18.27 |
| nitrogen | 111 | 300.55 | 17.81 |
| oxygen | 127 | 292.25 | 20.18 |
| carbon dioxide | 240 | 293.15 | 14.8 |
| carbon monoxide | 118 | 288.15 | 17.2 |
| hydrogen | 72 | 293.85 | 8.76 |
| ammonia | 370 | 293.15 | 9.82 |
| sulfur dioxide | 416 | 293.65 | 12.54 |
| helium | 79.4 [15] | 273 | 19 [16] |
See also [1].
Viscosity of a dilute gas
The Chapman-Enskog equation[17] may be used to estimate viscosity for a dilute gas. This equation is based on a semi-theoretical assumption by Chapman and Enskog. The equation requires three empirically determined parameters: the collision diameter (σ), the maximum energy of attraction divided by the Boltzmann constant (є/к) and the collision integral (ω(T*)).
with
- T* = κT/ε — reduced temperature (dimensionless),
- μ0 = viscosity for dilute gas (μP),
- M = molecular mass (g/mol),
- T = temperature (K),
- σ = the collision diameter (Å),
- ε / κ = the maximum energy of attraction divided by the Boltzmann constant (K),
- ωμ = the collision integral.
Liquids
In liquids, the additional forces between molecules become important. This leads to an additional contribution to the shear stress though the exact mechanics of this are still controversial.[citation needed] Thus, in liquids:
- Viscosity is independent of pressure (except at very high pressure); and
- Viscosity tends to fall as temperature increases (for example, water viscosity goes from 1.79 cP to 0.28 cP in the temperature range from 0 °C to 100 °C); see temperature dependence of liquid viscosity for more details.
The dynamic viscosities of liquids are typically several orders of magnitude higher than dynamic viscosities of gases.
[edit] Viscosity of blends of liquids
The viscosity of the blend of two or more liquids can be estimated using the Refutas equation[18][19]. The calculation is carried out in three steps.
The first step is to calculate the Viscosity Blending Number (VBN) (also called the Viscosity Blending Index) of each component of the blend:
- (1)
where v is the kinematic viscosity in centistokes (cSt). It is important that the kinematic viscosity of each component of the blend be obtained at the same temperature.
The next step is to calculate the VBN of the blend, using this equation:
- (2)
where xX is the mass fraction of each component of the blend.
Once the viscosity blending number of a blend has been calculated using equation (2), the final step is to determine the kinematic viscosity of the blend by solving equation (1) for v:
- (3)
where VBNBlend is the viscosity blending number of the blend.

No comments:
Post a Comment