The viscosity of air and water are by far the two most important materials for aviation aerodynamics and shipping fluid dynamics. Temperature plays the main role in determining viscosity.
Viscosity of air
The viscosity of air depends mostly on the temperature. At 15.0 °C, the viscosity of air is 1.78 × 10−5 kg/(m·s) or 1.78 × 10−4 P. One can get the viscosity of air as a function of temperature from the Gas Viscosity Calculator
Viscosity of water
The dynamic viscosity of water is 8.90 × 10−4 Pa·s or 8.90 × 10−3 dyn·s/cm2 or 0.890 cP at about 25 °C.
As a function of temperature T (K): μ(Pa·s) = A × 10B/(T−C)
where A=2.414 × 10−5 Pa·s ; B = 247.8 K ; and C = 140 K[citation needed].
Viscosity of liquid water at different temperatures up to the normal boiling point is listed below.
| Temperature [°C] | Viscosity [Pa·s] |
|---|---|
| 10 | 1.308e-3 |
| 20 | 1.003e-3 |
| 30 | 7.978e-4 |
| 40 | 6.531e-4 |
| 50 | 5.471e-4 |
| 60 | 4.668e-4 |
| 70 | 4.044e-4 |
| 80 | 3.550e-4 |
| 90 | 3.150e-4 |
| 100 | 2.822e-4 |
Viscosity of various materials
Some dynamic viscosities of Newtonian fluids are listed below:
Gases (at 0 °C):
| | viscosity [Pa·s] |
|---|---|
| hydrogen | 8.4e-6 |
| air | 17.4e-6 |
| xenon | 2.12e-5 |
Liquids (at 25 °C):
| | viscosity [Pa·s] | viscosity [cP] |
|---|---|---|
| acetone[20] | 3.06e-4 | 0.306 |
| benzene[20] | 6.04e-4 | 0.604 |
| blood (37 °C)[21] | 3e-3 to 4e-3 | 3–4 |
| castor oil[20] | 0.985 | 985 |
| corn syrup[20] | 1.3806 | 1380.6 |
| ethanol[20] | 1.074e-3 | 1.074 |
| ethylene glycol | 1.61e-2 | 16.1 |
| glycerol[22] | 1.5 | 1500 |
| HFO-380 | 2.022 | 2022 |
| mercury[20] | 1.526e-3 | 1.526 |
| methanol[20] | 5.44e-4 | 0.544 |
| nitrobenzene[20] | 1.863e-3 | 1.863 |
| liquid nitrogen77K | 1.58e-4 | 0.158 |
| propanol[20] | 1.945e-3 | 1.945 |
| olive oil | .081 | 81 |
| pitch | 2.3e8 | 2.3e11 |
| sulfuric acid[20] | 2.42e-2 | 24.2 |
| water | 8.94e-4 | 0.894 |
Fluids with variable compositions, such as honey, can have a wide range of viscosities.
| | viscosity [Pa.s] | viscosity [cP] |
|---|---|---|
| honey | 2,000–10,000 | 2,000,000–10,000,000 |
| molasses | 5,000–10,000 | 5,000,000–10,000,000 |
| molten glass | 10,000–1,000,000 | 10,000,000–1,000,000,000 |
| chocolate syrup | 10,000–25,000 | 10,000,000–25,000,000 |
| molten chocolate* | 45,000–130,000 [23] | 45,000,000–130,000,000 |
| ketchup* | 50,000–100,000 | 50,000,000–100,000,000 |
| peanut butter | ~250,000 | ~250,000,000 |
| shortening* | ~250,000 | 250,000,000 |
* These materials are highly non-Newtonian.
Viscosity of solids
On the basis that all solids such as granite[24] flow to a small extent in response to small shear stress, some researchers[25] have contended that substances known as amorphous solids, such as glass and many polymers, may be considered to have viscosity. This has led some to the view that solids are simply liquids with a very high viscosity, typically greater than 1012 Pa·s. This position is often adopted by supporters of the widely held misconception that glass flow can be observed in old buildings. This distortion is more likely the result of the glass making process rather than the viscosity of glass.[26]
However, others argue that solids are, in general, elastic for small stresses while fluids are not.[27] Even if solids flow at higher stresses, they are characterized by their low-stress behavior. This distinction can become muddled if measurements are continued over long time periods, such as the Pitch drop experiment. Viscosity may be an appropriate characteristic for solids in a plastic regime. The situation becomes somewhat confused as the term viscosity is sometimes used for solid materials, for example Maxwell materials, to describe the relationship between stress and the rate of change of strain, rather than rate of shear.
These distinctions may be largely resolved by considering the constitutive equations of the material in question, which take into account both its viscous and elastic behaviors. Materials for which both their viscosity and their elasticity are important in a particular range of deformation and deformation rate are called viscoelastic. In geology, earth materials that exhibit viscous deformation at least three times greater than their elastic deformation are sometimes called rheids.
Viscosity of amorphous materials
Viscous flow in amorphous materials (e.g. in glasses and melts)[29][30][31] is a thermally activated process:
where Q is activation energy, T is temperature, R is the molar gas constant and A is approximately a constant.
The viscous flow in amorphous materials is characterized by a deviation from the Arrhenius-type behavior: Q changes from a high value QH at low temperatures (in the glassy state) to a low value QL at high temperatures (in the liquid state). Depending on this change, amorphous materials are classified as either
- strong when: QH − QL < QL or
- fragile when: QH − QL ≥ QL.
The fragility of amorphous materials is numerically characterized by the Doremus’ fragility ratio:
and strong material have RD <>RD ≥ 2.
The viscosity of amorphous materials is quite exactly described by a two-exponential equation:
with constants A1, A2, B, C and D related to thermodynamic parameters of joining bonds of an amorphous material.
Not very far from the glass transition temperature, Tg, this equation can be approximated by a Vogel-Fulcher-Tammann (VFT) equation.
If the temperature is significantly lower than the glass transition temperature, T < Tg, then the two-exponential equation simplifies to an Arrhenius type equation:
with:
where Hd is the enthalpy of formation of broken bonds (termed configurons) and Hm is the enthalpy of their motion. When the temperature is less than the glass transition temperature, T Tg, the activation energy of viscosity is high because the amorphous materials are in the glassy state and most of their joining bonds are intact.
If the temperature is highly above the glass transition temperature, T Tg, the two-exponential equation also simplifies to an Arrhenius type equation:
with:
When the temperature is higher than the glass transition temperature, T Tg, the activation energy of viscosity is low because amorphous materials are melt and have most of their joining bonds broken which facilitates flow.
Volume (bulk) viscosity
The negative-one-third of the trace of the stress tensor is often identified with the thermodynamic pressure,
which only depends upon the equilibrium state potentials like temperature and density (equation of state). In general, the trace of the stress tensor is the sum of thermodynamic pressure contribution plus another contribution which is proportional to the divergence of the velocity field. This constant of proportionality is called the volume viscosity.
Eddy viscosity
In the study of turbulence in fluids, a common practical strategy for calculation is to ignore the small-scale vortices (or eddies) in the motion and to calculate a large-scale motion with an eddy viscosity that characterizes the transport and dissipation of energy in the smaller-scale flow (see large eddy simulation). Values of eddy viscosity used in modeling ocean circulation may be from 5x104 to 106 Pa·s depending upon the resolution of the numerical grid.
Fluidity
The reciprocal of viscosity is fluidity, usually symbolized by φ = 1 / μ or F = 1 / μ, depending on the convention used, measured in reciprocal poise (cm·s·g−1), sometimes called the rhe. Fluidity is seldom used in engineering practice.
The concept of fluidity can be used to determine the viscosity of an ideal solution. For two components a and b, the fluidity when a and b are mixed is
which is only slightly simpler than the equivalent equation in terms of viscosity:
where χa and χb is the mole fraction of component a and b respectively, and μa and μb are the components pure viscosities.
[edit] The linear viscous stress tensor
Viscous forces in a fluid are a function of the rate at which the fluid velocity is changing over distance. The velocity at any point r is specified by the velocity field v(r). The velocity at a small distance dr from point r may be written as a Taylor series:
where dv / dr is shorthand for the dyadic product of the del operator and the velocity:
This is just the Jacobian of the velocity field.
Viscous forces are the result of relative motion between elements of the fluid, and so are expressible as a function of the velocity field. In other words, the forces at r are a function of v(r) and all derivatives of v(r) at that point. In the case of linear viscosity, the viscous force will be a function of the Jacobian tensor alone. For almost all practical situations, the linear approximation is sufficient.
If we represent x, y, and z by indices 1, 2, and 3 respectively, the i,j component of the Jacobian may be written as ∂i vj where ∂i is shorthand for ∂/∂xi. Note that when the first and higher derivative terms are zero, the velocity of all fluid elements is parallel, and there are no viscous forces.
Any matrix may be written as the sum of an antisymmetric matrix and a symmetric matrix, and this decomposition is independent of coordinate system, and so has physical significance. The velocity field may be approximated as:
where Einstein notation is now being used in which repeated indices in a product are implicitly summed. The second term from the right is the asymmetric part of the first derivative term, and it represents a rigid rotation of the fluid about r with angular velocity ω where:
For such a rigid rotation, there is no change in the relative positions of the fluid elements, and so there is no viscous force associated with this term. The remaining symmetric term is responsible for the viscous forces in the fluid. Assuming the fluid is isotropic (i.e. its properties are the same in all directions), then the most general way that the symmetric term (the rate-of-strain tensor) can be broken down in a coordinate-independent (and therefore physically real) way is as the sum of a constant tensor (the rate-of-expansion tensor) and a traceless symmetric tensor (the rate-of-shear tensor):
where δij is the unit tensor. The most general linear relationship between the stress tensor σ and the rate-of-strain tensor is then a linear combination of these two tensors:[32]
where ς is the coefficient of bulk viscosity (or "second viscosity") and μ is the coefficient of (shear) viscosity.
The forces in the fluid are due to the velocities of the individual molecules. The velocity of a molecule may be thought of as the sum of the fluid velocity and the thermal velocity. The viscous stress tensor described above gives the force due to the fluid velocity only. The force on an area element in the fluid due to the thermal velocities of the molecules is just the hydrostatic pressure. This pressure term (−p δij) must be added to the viscous stress tensor to obtain the total stress tensor for the fluid.
The infinitesimal force dFi on an infinitesimal area dAi is then given by the usual relationship:

No comments:
Post a Comment